Full Tear-Off and Haul-Off
The old roof comes off in full and is hauled away, down to the deck, because a new installation over two old layers is not an installation at all.
A new roof is a system, not a finish, and the installation is judged by the layers nobody sees: the deck, the underlayment, the flashing and the ventilation underneath the shingles.
The old roof comes off in full and is hauled away, down to the deck, because a new installation over two old layers is not an installation at all.
Decking that is soft, rotted or delaminated is inspected and repaired before the new material goes down, and you see the bad sheets before they are covered.
Underlayment and flashing go on as one system, with new flashing at every penetration, chimney, wall and valley, because the flashing is where a new roof most often starts leaking.
Shingles go on over a ridge vent, with the soffit intake confirmed open, so the attic breathes and the new shingles are not cooked from below.
The City re-roof permit is pulled and the final inspection closes the job, because a new roof without a permit is a problem at the next sale.
Cleanup and the final walk-through close the job: the debris is hauled off, the yard is magnet-swept, and the finished roof is walked with you before we leave.
Roof installation in San Antonio is a new roof built in the right order: tear-off to the deck, decking repair, underlayment, flashing, finish, and ventilation balanced to the attic. The order matters more than any single layer, because a finish over a wet deck or old flashing is a new roof with an old leak. A change of pitch or a change of material to tile needs an engineer's report before the work starts, and the permit is pulled before the tear-off, not after.
The material choice shapes the install. Architectural shingles are the citywide default and realistically last 15 to 20 years here; standing-seam metal and tile last longer and weigh more, and tile needs an engineered structure. A roof inspection of the existing roof and deck tells you which options your house can carry before you choose.
An installation runs in a fixed order, and the order is the quality. Here is how a new roof goes on, from the first call to the final walk-through.
Schedule
Call (254) 645-5833 during hours and tell us the age of the roof and what you are seeing. We set a time to inspect, and the inspection covers the deck, the flashing and the ventilation.
Diagnose
We inspect every slope, photograph the wear and the flashing, and check the attic side of the deck, so the scope is written from the roof in front of us, not from a general idea.
Fix
You get a written scope for the installation, naming the material, the underlayment, the flashing work and the ventilation, so the decision is specific.
Finish
We tear off to the deck, rebuild in order, photograph each layer, sweep the yard, and walk the finished roof with you before we leave.
Roofing nail gun
On an installation the nail gun sets every fastener to the same depth, which is what holds the finish through a squall line and the next hail season.
Moisture meter
The moisture meter reads the deck before the underlayment goes down, finding the soft sheets that have to be replaced before the new roof covers them.
Chalk line and shingle cutter
We use the chalk line and shingle cutter on every installation, because a straight course and a clean cut are what make a new roof shed water evenly.
Pry bar and roofing hammer
The pry bar and roofing hammer strip the old roof and open the deck for inspection, which is the only way to know what the new roof is sitting on.
Safety harness and roofing ladder
On an installation the safety harness and roofing ladder are how steep slopes get worked without rushing, because a rushed footing is how a good job turns into a bad day.
Roofing hammer and utility knife
We use the roofing hammer and utility knife on every installation for the cuts and the fastening the nail gun cannot reach, at hips, ridges and penetrations.
Deck first, finish last
Deck first, finish last is the rule on every installation we do in San Antonio: the deck is inspected and repaired before any new material goes down.
Manufacturer-spec nailing pattern
For installation, the manufacturer-spec nailing pattern is what keeps the roof dry through hail season and the next hot summer, with the fastener count the pattern calls for at 108 mph design wind.
New flashing at every penetration
We follow new flashing at every penetration on installation work, because the flashing is the part that fails first and the part a shortcut leaves behind.
Balanced ventilation design
Balanced ventilation design is the rule on every installation we do in San Antonio: ridge exhaust matched to soffit intake, so the attic moves air instead of storing heat.
01
What we do: We measure the roof by age and wear: granules in the gutters, dark streaks on the north slope, and a mat that has given 18 to 25 summers in this heat. That is a roof at the end of its years, not a roof with one bad detail.
The homeowner gets a written scope for the installation, with photos of the worn slopes and the material named, so the decision is specific instead of general.
02
What we do: We photograph the hail bruising slope by slope and count the hits, then compare the damage against the age of the roof, because a bruised 20-year-old roof is a replacement, not a repair.
The installation scope is written, the photos are in hand, and the homeowner can act on the roof with the evidence in front of them.
03
What we do: We read the inspection report with you, slope by slope, and say plainly whether the roof has years left or whether the inspector has found the end of them.
The roof is documented, the installation is scoped, and the homeowner decides with the evidence in hand rather than a guess.
04
What we do: We price the addition or the re-roof with the material change in the open: a change to metal or to Class 4 impact shingles, the underlayment it needs, and the permit it requires.
The homeowner keeps photos of the damage and a written scope for the installation, so the next step is a decision, not a guess.
A new roof in San Antonio has to face hail season, 100-degree summers, and clay soils that shift under the slab, all at once. The installation is planned for all three, and the material is chosen for the house it goes on.
Alamo Ranch
Alamo Ranch is far-west master-planned building from the 1990s onward, where newer large-format shingle roofs are entering their first replacement window and the installation is often the first roof the house has had.
Stone Oak
In Stone Oak the installation work follows the neighbourhood: 1990s and newer streets, tile-heavy blocks beside architectural shingle ones, and HOA rules that name the material and the colour.
Westover Hills
Westover Hills is far-west master-planned building where the roofs are newer and larger, and the installation is planned around the era and the roof type the streets actually have.
Encino Park
Encino Park sits in the far north along the Bulverde Road corridor, where master-planned streets from the 1990s onward carry architectural shingle and tile side by side.
Thousand Oaks
In Thousand Oaks the installation work follows the neighbourhood: 1980s streets on their second or third roof, where the decision is usually about age, not about one storm.
Spring hail season across Bexar County
Spring hail season across Bexar County runs March through May, when about 85 percent of the large-hail reports fall, and a new roof is installed with that calendar in mind.
Summer UV and 100-degree heat
When we plan installation work, summer UV and 100-degree heat is on the list from the first look, because a new roof over a hot attic ages from below as surely as from above.
Expansive clay soils
Expansive clay soils shape how installation work is done in this city: the ground swells wet and shrinks dry, the frame moves, and the flashing and valley joints take the movement.
Design wind speed of 108 mph
Design wind speed of 108 mph is part of every installation here, and the nailing pattern and the fastener count are set to the adopted code, not to habit.
Most roofs do not fail all at once. They fail at a flashing detail, a cracked boot, or a slope that lost its granules, and the damage spreads from the detail outward, which is why an installation starts with the deck and the details, not the finish.
Problem
Missing shingles after a wind event leave the underlayment exposed to the next rain, and a roof that has lost shingles across several slopes is usually telling you the mat is done.
Our Fix
The fix for missing shingles after a wind event is a full installation when the mat has failed across the roof, with the deck inspected and the soft sheets replaced before the new system goes on.
Problem
Hail bruising that has not leaked yet still breaks the shingle mat, and the granule loss that follows lets UV at the asphalt, which is how a bruise becomes a leak a season or two later.
Our Fix
We address hail bruising that has not leaked yet by documenting it slope by slope, so the installation scope names the damage while the roof is still dry inside.
Problem
Recurring leaks at chimney and skylight flashing are the most common leak source on an ageing roof, because the flashing moves with the frame and the sealant gives up long before the shingles do.
Our Fix
We fix the cause of the recurring leaks at chimney and skylight flashing by replacing the flashing at every penetration during the installation, not by resealing what has already failed.
Problem
A sagging roofline and soft decking usually mean the deck has been wet for a long time, and it is found by walking the roof and feeling the give underfoot, not from the driveway.
Our Fix
The fix for a sagging roofline and soft decking starts with the deck: the soft sheets come out, the framing is checked, and the new roof goes on a sound structure.
A new roof with proper ridge and soffit ventilation takes heat out of the attic, and new flashing at every penetration ends the leak-chasing. Compare architectural shingles with Class 4 impact-resistant shingles if hail is your main worry.
A system built in the right order
A system built in the right order is built into the roof installation work, not added on top of it: deck, underlayment, flashing, finish, ventilation, each in its turn.
Ventilation that takes heat out
With roof installation, ventilation that takes heat out is the difference between shingles that last their years and shingles that curl early, which is why the ridge vent and the soffit intake are part of the scope.
Flashing replaced at every detail
Flashing replaced at every detail is one of the reasons homeowners choose our roof installation work, because the flashing is where most roofs fail and the part a shortcut leaves behind.
A permit pulled and a final check done
A permit pulled and a final check done is built into the roof installation work, not added on top of it, so the new roof is on the City's record as well as ours.
Kbron Roofing holds 5.0 out of 5 from 18 Google reviews, all 5-star. Reviewers name Rene Vargas as their contact and describe honest, no-pressure service. Read short verbatim excerpts from those reviews in the Roof Installation testimonials below.
We install roofs across Bexar County housing stock, from new additions to full re-roofs, and we put our name and address on the work: Kbron Roofing, 6 Irongate Creek, San Antonio, TX 78238. Call (254) 645-5833 during hours.
Short verbatim excerpts from Google reviews by customers who chose our roof installation work. All five readable reviewers gave 5 stars two months ago; three are quoted below.
"Rene is incredibly honest, hardworking, and dedicated to his customers. He takes the time to truly understand your needs and delivers quality work and results at a price that won't break your wallet."
Joe Favor
★★★★★ · Homeowner, San Antonio · 2 months ago · Roof inspection, roof installation, storm and wind repair
"He was so professional, walked me through the steps of how to make a claim with my insurance, and the whole process was super simple. The roof was installed in just one day, and the crew was incredibly clean and professional."
Donnovan Smith
★★★★★ · Homeowner, San Antonio · 2 months ago · Storm and wind repair, roof installation
"They started early in the morning and finished the same day. They cleaned up very well. They were extremely knowledgeable and patient."
Doris Longoria
★★★★★ · Homeowner, San Antonio · 2 months ago · Roof installation after hail damage
Real answers to the questions we hear most often about roof installation in San Antonio, including what sits under the shingles.
Roof Replacement pairs with roof installation on many San Antonio homes, and the two scopes are written together so nothing is missed.
View Roof ReplacementWhere roof installation work raises a question, roof repair is often the answer, and we scope it in the same visit.
View Roof RepairResidential Roofing is the natural next step after roof installation on a roof that needs more than one kind of attention.
View Residential RoofingRoof Inspection pairs with roof installation on many San Antonio homes, and the two scopes are written together so nothing is missed.
View Roof InspectionWhere roof installation work raises a question, roof maintenance is often the answer, and we scope it in the same visit.
View Roof MaintenanceMetal Roofing is the natural next step after roof installation on a roof that needs more than one kind of attention.
View Metal RoofingCall us at (254) 645-5833 or send a message and we will get back to you during business hours. We schedule installations Monday to Saturday, 6 AM to 8 PM.
Phone
(254) 645-5833Address
6 Irongate Creek, San Antonio, TX 78238, United States, San Antonio, Texas
Hours
Mon–Sat: 6 AM – 8 PM